How to install Laminate Flooring
Welcome to our simple guide to installing your new laminate floors. You're going to love just how quick and easy it is to lay your new laminate floors.Download Installation Guide
Before you begin, check for the following
• Signs of Moisture in your subfloor
• Leaky equipment, fixtures and seals
• Subfloor is level according to relevant industry standards (3mm deviation over 1m)
• No underfloor heating
• Optimal laying conditions (Room temperature 15-30 degrees)
• Humidity levels (Between 30-70%)
• Appropriate window furnishings are installed
Acclimatise your laminate floors
When you've received your laminate floors it is essential to acclimatise them in the centre of the room before installing.
Up to one week’s acclimatisation is essential in areas that are particularly humid, cold, wet, hot or dry. Boards installed in a humid environment will naturally grow, hence the requirement for acclimatisation in areas such as QLD.
Maximum Raft Size - (L) 10m x (W) 8m
OK it's time to start installing, let's take it step by step
• Pre-select boards that blend best with matching scotia, skirts and trims.
• Stagger boards to ensure a more favourable overall appearance of the floor. When installing boards of random length, ensure that the staggered length is at least 20cm. End boards must be greater than 30cm in length.
• Check door and door frame clearances to ensure that doors will move freely without contacting the floor surface.
• Although floating floors can be installed in any direction, as a rule, they are usually installed perpendicular to a window. Installing the floor parallel to the longest wall tends to make a room appear larger.
Step 1. First plank, first row. Place a spacer 10-15mm thickness to the left and position the plank against the wall. Later, after 3 rows, you can easily position the flooring against the front wall with spacers of 10-15mm.
Step 2. Second plank, first row. Press the short end of the next floorboard at an angle to the first one, then lay down, complete the first row. The boards can also be lightly tapped up without lifting.
Step 3 At the end of the first row, place a spacer 10-15mm to the wall and cut the length of the last plank to fit.
Step 4. For a clean cut, the top surface should face down when you use a jigsaw, circular handsaw or guillotine, and up when you use a handsaw or a crosscut saw.
Step 5. Second row, first plank. Minimum length 300mm. Place a spacer against the wall.
Step 6. Minimum distance between short ends of planks in parallel shall not be less than 200mm.
Step 7. Place the floorboard at an angle against the floorboard in the previous row, press forward and fold down at the same time. A rubber mallet and tapping block may be necessary.
Step 8. Second plank, second row. Place the short end of the floorboard at an angle against the previously installed floorboard. Fold down. The boards can also be tapped up without lifting.
Step 9. Lift floorboard (together with the previously installed floorboard in the same row) lightly up (about 30mm) and push it against the row in front. Push down when the floorboards are positioned tightly together.
Step 10. After 2-3 rows, adjust the distance to the front wall by placing spacers 10-15mm
Step 11. If the wall is uneven, the floorboards must be adapted to its contours. Mark the floorboards with the contour of the wall. Do not forget to leave a 10-15mm space to the wall.
Step 12. To remove the first row, lift the floorboard a few centimetres and tap along the joint. Cut the floorboards as required.
Step 13. Reinstall the first row from left to right. Press the boards against the edges of the floorboards that are already in position, with the first strip.
Step 14. Last row. Minimum width 30mm. Remember, the space to the wall is 10-15mm.
TIP! Place a spacer before measuring. Cut the panels lengthwise and install.
Lastly, Get Insta Ready
Congrats, you did it! Before you kick back and admire a job well done, don’t forget to snap some photos and share your new floors. Tag us on Instagram @flooringonlineau to really make our day.